Ge vhf raqdio manual
When you raqdio reach the manual last slug, set the tracking generator to output -30dBm and connect the SA Input raqdio back to the LO raqdio Output of the receiver Front End module.
Verify that the VCO is locked throughout the 2-Meter band by retesting on raqdio 146.000 and 148.000 MHZ.
Tuning can be done two ways: Place the Synthesizer back into the T/R frame and adjust the VCO capacitor, C52 raqdio with a 'greenie' until the Fault LED extinguishes.
C) Whether this is to be high power or LOW power channel.
Verify they do not overlap the tuning slugs before purchase.Power off raqdio the radio and remove the cables from the power supply.It just needs a light coat.Phase 3 - VHF Receiver Synthesizer Module: Please Refer to LBI38641B Please note that the Group 1 ( MHz) Synthesizer generates high side Local Oscillator injection where as the Group 2 (150.8 - 174 MHz) generates low side.Isopropyl alcohol works if that is all you have.Once tuned, remove the module from the frame again and replace manual RF shield.Of course we could just remove the filters but that would offer no image rejection and selectivity would take a hit.You will need a copy of TQ-3353 mastr-IIe, III Programming Software (T, T).Tin the nut and slug as above and then place the nut on the slug cold.The cleaner it is, the better.Locate a small variable resistor labeled RV-1 (near the exact center of the radio next to ribbon cable jumper J4).
It is important that the software be in mastr III mode.
The MPD-Scan is a mazak MPD with 4 buttons on the front panel which control the scanning function.
TXL - "Transmit lock" to keep you checkbook checkbook from transmitting if there is a lathe signal on frequency (recommend value of NO or you will be waiting for a repeater to drop carrier before you can transmit).To test for conversion gain, set the Spectrum Analyzer center frequency.4 chorus MHz.Connect a jumper from the Watt meter to the dummy load.One small sharp knife (X-Acto type).The transceiver can be loaded with 16 channels (one mode) at a time complete with transmit and receive frequencies, ctcss (PL) tones and 8 character Alphanumeric channel identifiers.I cannot, nor will not, be responsible for damage to equipment caused by modifications YOU make to the radio as a result of your reading this document.Reconnect the power supply and power the radio.The correct programming cable to go between the PC interface box and the radio "mike connector" located above the PTT.(See drawing B for help locating these adjustment points).Set a scanner/receiver for 144.000 MHZ and set it within 2 feet of the dummy load.The old C19 is placed next to C6 with some solder mask scraped to make a new ground plane.If windows the radio is transmitting with more than 5 watts and/or is not at the LOW power wattage you want; A) Adjust the "tracking" settings through the following keystrokes from the main menu psps of the software.What would be nice to have:.Adjust the Power Output manual value in the software until the desired power level is achieved.If the VCO is causing a squealing on the transmitted signal, carefully adjust CV-202 until the transmitted audio squeal stops.
Clean solder flux with alcohol ge vhf raqdio manual and a toothbrush.
Send programming data to the repeater by pressing F5 and selecting the file you just edited.
This will make midnight you speculate your winnings in order to afford the cars you need.Report Issue, post navigation.As always you have the driving skills but two things are missing: money and reputation. Related Games: share, facebook, whatsapp, reddit.Use them anytime you can because driversRead more
Driver Genius Professional driver 1 serial - 766 Byte, driver Genius Professional 6 patch -.59 MB, driver Genius Professional 6 Portable -.25.Driver Genius Professional 4 crack -.94 MB, driver Genius Professional 6 crack -.90 MB, driver Genius Professional 1 crack -.49. PicturesToExe Deluxe.0.17 (2015) PCRead more
Do not insert any object through the diagnostic cooling slots of the engine.Store the equipment in a clean and dry area. Approximately 620ml (21.) are required without an oil filter; 770ml (29.) with repair an oil filter.If you believe the engine is running too fastRead more